1. Duration of the procedure with the “AndroSPOK” device is 20 minutes (i.e., 2 operation cycles – see below).

2. The duration of one cycle of the device is 10 minutes. A sound signal is heard every minute for 10 minutes (use this as a guide for proper vacuum control with a hand pump). After 10 minutes of operation, the device emits a long signal and turns off.

3. The device is controlled by two buttons:
[0] – “Color” button is designed to select the color of the optical effect;
[I] – “Start” button is designed to turn on the electromagnetic inductor and start the pulse exposure by light (when you press the [I] – “Start” button, light-emitting diodes begin to blink).

There are two buttons to control the “AndroSPOK”

4. When you plug in the device, blue light-emitting diodes turn on by default. Each time you press [0] – “Color” button, the type of optical effect changes cyclically in the following sequence: – blue; – green; – yellow; – red; – blue with infrared; – green with infrared; – yellow with infrared; – red with infrared; – blue; – green; – yellow, etc. on loop.

5. The choice of a combined effect of visible and infrared radiation is accompanied by a short signal.

6. To select the type of optical exposure, see below.

7. When installing a vacuum flask inside the electronic vacuum-erector, it is necessary to get the sleeve on the flask into the groove on the electronic vacuum-erector. To prevent damage to the device, avoid physical effort when assembling and disassembling the device!

8. The procedure is performed while sitting.

9. For the correct procedure in order to better retain the vacuum in the flask, it is recommended to shave the pubic hair (or, otherwise, apply a layer of thick Vaseline to the edge of the vacuum flask).

10. To perform the procedure, the penis is placed in a vacuum flask. For a better glide of the penis head along the wall of the flask, it is recommended to lubricate the head.

11. The correct procedure involves the alternation of vacuum with rest (the discharge of vacuum by using the valve on the manual pump). See below for details.

It is forbidden
to keep the penis in vacuum for more than 10 minutes!
Do not create too much vacuum in the vacuum flask! The procedure should not cause pain. Optimally matched pressure corresponds to the stiff penis, bursting sensations and tingling in the head of the penis.

General operation algorithm of the “AndroSPOK” device

1. Prepare for the procedure in advance – remove the pubic hair.

2. Use the device in assembled form: vacuum flask is installed inside the electronic vacuum-erector, the fitting of the hand pump is installed on the thread of the vacuum flask, the device is plugged in.

3. Select the desired optical effect (see below and use the [0] – “Color” button).

4. Place the penis in the vacuum flask, pre-lubricate the head.

The scrotum is located outside the flask during the procedure
(click to watch the video)

5. Using a hand pump, slowly, without rash, create vacuum in the vacuum flask. Remember that the filling of the cavernous bodies of the penis with blood under the influence of local negative pressure does not occur instantly. Gradually increase the negative pressure in the flask until you get an erection and your penis becomes stiff.

6. Turn the device on using the [I] – “Start” button.

7. Maintain erection with a hand pump for about 30 seconds. Then release the vacuum using the valve button on the pump.

8. Wait about 30 seconds without removing the penis from the flask.

9. Using the manual pump again, slowly create a vacuum in the vacuum flask until you get an erection. Maintain erection with a hand pump for about 30 seconds. Then release the vacuum using the valve button on the pump.

10. Wait about 30 seconds without removing the penis from the flask.

11. Follow this vacuum control scheme throughout the procedure.

12. After 10 minutes, the device will turn off with a long signal. Discharge the vacuum. Press the [0] button to select a different type of optical exposure as indicated below. Again turn the device on using the [I] – “Start” button.

13. Having repeated the above algorithm, perform the second cycle of the procedure.

14. After the 3rd procedure, begin to gradually increase the time of maintaining an erection with a hand pump. By the end of the course you should hold the vacuum in the flask for up to 40-50 seconds, alternating this with rest for only 10-20 seconds.

15. The standard course of treatment using the “AndroSPOK” device is 10-12 procedures. It is allowed to increase the duration of treatment to 25-30 procedures per course. Interval between courses is 6-8 weeks.

16. For the best sustainable effect, it is recommended to repeat physical therapy every 1.5 – 2 months.

Choice of the type of optical exposure,
depending on the intended use of the “AndroSPOK” device
  1. Treatment of erectile dysfunction:

– in the first cycle of the device (10 minutes), a combination of visible red light with infrared radiation is used (the choice of such a combination corresponds to red light together with a sound signal);

– in the second cycle of the device (10 minutes), a combination of visible green light with infrared radiation is used (the choice of such a combination corresponds to green light together with a sound signal).

  1. Treatment of chronic prostatitis:

– in the first cycle of the device (10 minutes), a combination of visible blue light with infrared radiation is used (the choice of such a combination corresponds to blue light together with a sound signal);

– in the second cycle of the device (10 minutes), a combination of visible green light with infrared radiation is used (the choice of such a combination corresponds to green light together with a sound signal).

  1. Treatment of premature ejaculation (rapid ejaculation):

– in the first cycle of the device (10 minutes), a combination of visible red light with infrared radiation is used (the choice of such a combination corresponds to red light together with a sound signal);

– in the second cycle of the device (10 minutes), a combination of visible yellow light with infrared radiation is used (the choice of such a combination corresponds to yellow light together with a sound signal).

  1. Treatment of Peyronie’s disease (fibroplastic penile induration):

– in the first cycle of the device (10 minutes), a combination of visible blue light with infrared radiation is used (the choice of such a combination corresponds to blue light together with a sound signal);

– in the second cycle of the device (10 minutes), a combination of visible blue light with infrared radiation is used (the choice of such a combination corresponds to blue light together with a sound signal).

  1. Prevention of diseases of the reproductive system in men:

– in the first cycle of the device (10 minutes), a combination of visible red light with infrared radiation is used (the choice of such a combination corresponds to red light together with a sound signal);

– in the second cycle of the device (10 minutes), a combination of visible green light with infrared radiation is used (the choice of such a combination corresponds to green light together with a sound signal).

Attention! Do the first 4-5 procedures of the course on a daily basis, all other procedures with an interval of 1-2 days. Try doing at least 3 procedures per week with approximately equal breaks between procedures. The standard course consists of 12 procedures. If necessary, you can increase the course of treatment to 25 – 30 procedures. A break between courses – 6 – 8 weeks.

HOW DOES IT WORK?
HOW TO BUY?
The “AndroSPOK” magnetophotobarotherapy device review
(you can turn on English subtitles in the video settings)

Place your order